RTA1025W 4 Port LAN & Wireless Router

Awesome Support

There are many modems which will work with our adsl services. As you can appreciate we can only support the hardware that we sell. However we have ammassed a wealth of information and screen shots which will assist you with your modem, even if you have an unsupport device. If this is not your modem please look at our general settings

Once you have connected the router to your computer, you can then proceed to configure your router.

Any router supplied by EscapeNet will be automatically configured, and therefore you do not need to go through this process.

1. Open Internet Explorer

Open Internet Explorer by clicking on its icon on your computer

2. Open Router's Management Interface

Enter the address http://192.168.1.1 and press ENTER

3. Login to the Router

Enter the username of admin and password of admin into this window. This authenticates you to the router. You can change these login details within the router, but that is beyond the scope of this document.

4. Configure the Router

Now enter your full EscapeNet email address as your broadband username, and your password. (The authentication is case sensitive).

5. Congratulations! your Connected

You are now connected and the settings are automatically saved. You can now browse the internet eg www.google.com

Specifications

ADSL Compliance

ADSL	ANSI T1.413 Issue 2 ITU G.992.1 Annex A (G.dmt) ITU G.992.2 Annex A (G.lite) ITU G.994.1 (G.hs) Support dying gasp Maximum Rate: 8 Mbps downstream and 1 Mbps upstream
ADSL2	ITU G.992.3 Annex A (G.dmt) ITU G.992.4 Annex A (G.lite) Maximum Rate: 12 Mbps downstream and 1 Mbps upstream
ADSL2+	ITU G.992.5 Annex A (G.dmt) Maximum Rate: 24 Mbps downstream and 1.2 Mbps upstream

ATM

PPPoA (RFC 2364) and PPPoA Bridged mode
PPPoE (RFC 2516) and PPPoE Bridged mode
IPoA (RFC 2225)
Bridged mode over AAL5 (RFC2684/1483)
ATM Forum UNI 3.1 / 4.0 compliant PVCs
UBR and CBR with traffic shaping
OAM F4/F5 loopback cells

Bridging

IEEE 802.1d self-learning bridge
Learning up to 4096 MAC addresses
Transparent Bridging between 10/100 Mb Ethernet and USB

Routing

NAT / PAT allows multiple users to share Internet access
UPnP IGD with NAT traversal capability
Port Forwarding: users can setup multiple virtual servers (e.g., Web, FTP, Mail servers) on the local network.
Static routing & dynamic routing RIPv1/v2
DNS Relay, Dynamic DNS
DHCP Client/Relay/Server
IGMP Proxy
Support IP/Bridge QoS for different traffic classes
Support reservation of bandwidth to guarantee voice quality of VoIP applications.

Security

PAP, CHAP, and MS-CHAP for PPP authentication
Firewall based on incoming & outgoing filtering of IP address/Port number/Protocol type
Ping blocking from WAN
DMZ hosting

Supported Applications

Application Level Gateways preset for Auth/Ident, DNS, FTP, PPTP, IPSEC, POP3, SMTP, SSH, TELNET, TFTP & WEB servers. Multiple Virtual Servers can be setup in local network.
VPN passthrough
NetMeeting, MSN Messenger, FTP, Quick Time, mIRC, Real Player, CuSeeMe, online gaming.

Configuration and Management

Embedded web configuration interface with password protection
Remote management control
Telnet session for local or remote management
System events logging
DSL connection diagnostics
Firmware upgrade via web browser
User setting backup & restore

Hardware Interface

One RJ-11 port for ADSL connection
One Ethernet port for IEEE 802.3/802.3u 10/100 Base-T auto-sensing, auto cross-over.
One USB port compliant to USB v1.1
One hidden reset button for restoring factory default settings

Chipset

Broadcom BCM6348 single-chip ADSL2+ with integrated MIPS32 CPU, transceiver & Analog Front End
Broadcom BCM4318 single-chip 802.11g wireless LAN solution

Wireless LAN

Supports IEEE 802.11g and 802.11b
Data Rates: 54, 48, 36, 24, 18, 12, 9, 6 Mbps for 802.11g and 11, 5.5, 2, 1 Mbps for 802.11b
Diversity antenna system: one external antenna and one internal antenna
Maximum RF output power: 15dBm for 802.11g
Coverage Area:
802.11g: LOS (Outdoors): Max. 50 meters;
Indoors: Max. 20 meters
802.11b: LOS (Outdoors): Max. 180 meters;
Indoors: Max. 60 meters
Support WEP (Wired Equivalent Privacy) RC4 with 64-bit or 128-bit key length
Support Access Control List, only registered WLAN clients are allowed
Support 802.1x, WPA-PSK, WPA, WPA2 & Mixed WAP/WPA2. Support SSID stealthing
Support repeater function to extend coverage
Support client isolation for wireless hotspot
Support SSID stealthing

Regulatory Approval and Compliance

ACA
Telecom New Zealand PTC270

Power Requirement and Operation Environment Requirement

Power Adaptor: Output 12 VAC, 1A
Power Consumption: less than 10 W
Ambient Temperature: 0 to 40°C
Relative Humidity: 20% to 90% (non-condensing)

Physical

Front Panel: 5 LED Indicators
Rear Panel
Dimensions: 190mm(L) x 130mm(W) x 40mm(H)
Weight: 350g

Firmware

Updating your Firmware is only recommended if you are having problems with your product or have been asked to do so by a NetComm Reprentative. It is critical to select the correct firmware for your product, before proceeding please confirm you are on the correct page by checking the sticker on the base of your NetComm equipment for the part/product number. You should also read the firmware upgrade instructions - located below - before starting the download.

Please take caution while upgrading the firmware. Installation of the incorrect firmware file, disruption to the power source or a break in the connection to your computer during the upgrade process may render your device unusable and void the product warranty.

Step 1 - Download the Firmware and Upgrade Instructions

RTA1025W NZ Firmware
RTA1025W_NZ_Firmware.zip (3.2 MB)
RTA1025W Rev1 AU Firmware
RTA1025W_AU_Firmware.zip (3.2 MB)

Step 2 - Before Installing firmware

Ensure that ALL Antivirus/ Firewall/ Security programs are turned OFF before performing the firmware upgrade. Also ensure that you are performing this firmware upgrade when connecting to the modem/router with Ethernet cable

Do NOT use a Wireless connection to upgrade the firmware.

Step 3 - Prepare the files

If the file's extension is ".dat", ".cdi", ".img" or ".bin", do not try to open the files on your computer as they can become corrupt. You need to follow the instructions from the Firmware Upgrade Instructions Guide.

If the file's extension is ".zip" then you need to unzip the compressed files to a location on your computer to get the actual firmware file using UnZip or WinZip software and then follow the instructions from the guide.

GNU General Public License

This product may include software code that is subject to the GNU General Public License (GPL) or GNU Lesser General Public License (LGPL). This code is subject to the copyrights of one or more authors and is distributed without any warranty. A copy of this software can be obtained by contacting NetComm Limited on +61 2 9424 2059. A postage and handling fee of AUD$10.00 will be applicable.

Residential

Business

Support